Traveling While Living Aboard

Living aboard has many advantages, one of which is the reduced cost of living. This can translate into saving for retirement while at the same time having extra money on hand for entertainment.

Maddie and I did a trip over Thanksgivings weekend to Iceland to try and see the Northern Lights. No, she didn't want to go by boat; we had to fly and leave our home behind for a few days.

Whenever you leave your boat for an extended period of time, it is advisable to take certain precautions before going.

Close all seacocks
Turn off all electronics
Leave on battery charger
Leave on bilge pumps
Tell a trusted neighbor

A hose can easily split or slip off of a fitting below the waterline, leaving a giant hole in the hull gushing in water. This is why frequent inspections are necessary to make sure that all hoses and fittings are in working order to avoid this from happening in the first place. Since you will be away for an extended period, it is best to close all seacocks. A closed seacock will not let water through, even if the hose slips off or splits. 

Turning off all electronics is another important step in leaving your boat. If a wire were to overheat and cause an electrical fire, it may create a good amount of smoke before the breaker trips. If the breaker is faulty, it could continue to burn and ignite other structures in the boat which could burn it to the waterline if left unchecked. 

Do leave on the automatic bilge pump and battery charger, that way if water does find its way inside, the pump can get it out and the charger can keep the pumps running if there is a leak.

Most importantly, tell a trusted neighbor that you are leaving. They can keep an eye on your waterline to make sure that you don't start sitting low in the water. I always give my neighbor a key to my boat when I leave so they can also get inside to take care of things should the situation arise. Make sure they know where your pumps are located, where the breaker panel is, which breaker is for the battery charger and the bilge pump, and where the lever is for the manual bilge pump, should the electronic ones fail.

Living on a boat gives you so much more freedom! You should take advantage of these freedoms while still taking good care of your home afloat. 

Jacklines

While there are many methods to recover a person after a "Man Overboard", the best measure is to avoid them!

While having good handholds, nonskid decks, and secure lifelines are all critical measures; I feel that clipping into Jacklines is a wonderful method to keep you attached to the boat at all times.

Jacklines are a line that runs uninterrupted from bow to stern. The idea is you can clip in and walk from bow to stern without having to unclip. This way, if you fall over, you will be attached to the boat. Instead of trying to recover a person in the water, you simply have to pull them back on deck. 

Most recommend using nylon webbing because it lays flat on the deck and won't roll underfoot. This is true, but I have found that they will slide underfoot and cause the same loss of balance. 

They also will suffer from UV degradation at an alarming rate. For this reason, they recommend only setting them up when conditions merit, to limit their sun exposure. When conditions merit is when you want to clip in, not when you want to rig them!

I use 1/2" 3 lay nylon rope for my jacklines. They are attached at the bow and stern cleats and run uninterrupted on the deck. They are the same material as dock lines and anchor rode, so I feel better about leaving them in the sun permanently rigged. The moment we feel the need to use them, we have them!

1/2" 3 lay will roll underfoot, so we simply don't step on it, just like we don't step on sheets or jib tracks or slippery painted parts. You will learn your deck and be able to navigate it in the dark!

Our rule is if we go on deck and we are not tied to a pier or anchored to the bottom, we are clipped in! Even on light air days, it would be really annoying to have to jibe the drifter around to pick someone up. If we are clipped in, then we are never disconnected.

There are occasions when we don't follow our own rules, but we both have to OK the decision. Maddie doesn't like to wear her life jacket and harness because it is hot and heavy. When conditions are very light and she is just going to sit on the deck, she will go without wearing it or being clipped in. The important part is we are all in accord on the decisions to keep each other safe while sailing.

Boat Dog!

Morty is our boat dog! Short legs for a low center of gravity and no tail to get caught in a winch!

He is a terrible swimmer, which is why we try so hard to keep him on board. 

He always wears a life jacket to help him float while he would wait for his recovery, if he were to fall over.

To avoid a "Dog Overboard" situation, we keep him tied to the jacklines that run the length of the deck, allowing him to walk around. I also wove a net on the bottom half of the lifelines to help keep him on board. 

The best way to keep him on the boat is to make sure that he is happy on the boat. Being how I raised him from a puppy on board Wisdom, this is his home and he doesn't try to escape (unless we leave without him, then he will jump off and chase after us).

New Gangplank: Part 5

The gangplank is now complete! 

The stanchions are secured in their bases and provide a very secure hand hold since they are through bolted and the lifelines are tight to give a nice feeling of security. The plank itself is much stronger and does not sag under your feet, keeping the lifelines tight!

My grandfathers brother was able to comfortably walk up the gangplank while using his cane to come aboard and visit! 

The old gangplank served it's purpose but this new one serves the purpose in luxury! 

If you would like me to make a gangplank for you as well, please contact me to set up an estimate.

New Gangplank: Part 4

Now that the gangplank has dried, it's time to install all the fittings.

The stanchion bases were bedded with 3M 4200 to allow difficult removal should the need arise. The opposite side was properly supported by the backing plate along with 1in washers and locking nuts. The through bolts were tightened down and the excess was exuded. 

The excess was then cleaned up with acetone, and left to cure for a few days.